Below are the available bulk discount rates for each individual item when you purchase a certain amount
Twin Tech Tactical has designed, and is manufacturing a fully machined polymer takedown lever to replace the weak factory piece. This takedown lever is far superior to the Ruger injection molded part in two ways.
First our parts are fully machined from a billet block of a super strong, high impact resistant polymer. This process insures that there are no defects in the material, such as hotspots, porosity, or cooling cracks that are inherent on the Ruger injection molded piece. Second our parts have more impact surface area than the original Ruger factory piece as you can see by the comparison photos.
Although our take down lever is superior to Ruger’s factory piece, it is not indestructible. There are a lot of different factors that will affect the life of our TDL that we have no control over, like: shooting suppressors wet with any ammo, hyper velocity ammo, improper installation, and homemade suppressors. We have made our best attempt to remedy a bad design and these parts should be considered a sacrificial piece that could fail at some point in the future.
Therefore no warranty is expressed or implied.
Due to Title 22 U.S.C. 2778 of the Arms Export Control Act (AECA) we cannot export beyond the U.S. Border and Territories.
Although our take down lever is superior to Ruger’s factory piece, it is not indestructible. There are a lot of different factors that will affect the life of our TDL that we have no control over, like: shooting suppressors wet with any ammo, hyper velocity ammo, improper installation, and homemade suppressors. We have made our best attempt to remedy a bad design and these parts should be considered a sacrificial piece that could fail at some point in the future. Therefore no warranty is expressed or implied
Showing reviews 1-10 of 17 | Next
Posted by Tim on Feb 6th 2017
Received take down lever in 3 days of order on a Sunday. Had it installed within 5 minutes of opening it. Very good quality and seems as though it will hold up much better than factory piece. Seems to even make slide fit a little snugger to frame. Very satisfied with price and quality. Will recommend.
Posted by Unknown on Dec 6th 2016
The takedown lever broke on my SR22 after just 27 rounds (nice job ruger) and after failing to find a factory replacement part for sale online, I turned to Twin Tech Tactical for an upgrade. The shipping was fast and the part is clearly a higher quality piece than the factory lever. I've only fired a few rounds with the new takedown lever but so far it has functioned flawlessly. One thing to note is that the detent on the new part is VERY strong and this results in some difficulty with opening and closing the takedown lever, however this does keep the lever from falling open during firing like the factory one did.
Posted by Roy on Sep 13th 2016
It fits like a glove, high quality. Fits so well, u cant undo it with just your finger, u need something like a screw driver. I dont know if its good or not. Thank you for fast delivery.
Posted by J V O Weaver on Jun 29th 2016
My SR22 takedown lever failed after 300 rounds. Searching Google, I found that Twin Tech made an aftermarket lever that is better (tested) than the original. After viewing the You Tube video on how to replace the broken part -- (thanks Twin Tech, that was awesome) -- I got busy and did the repair. My pistol functions flawlessly now and saved time and money in getting the pistol back on line. Great product, great service and tech support.
Posted by Unknown on Jun 11th 2016
Got the takedown lever exactly when they said I would. Watching the video was an easily install for the takedown lever. Couldn't be happier with the product
Posted by j leclerc on Jun 8th 2016
Top quality replacement part,positive locking detent,range session was without any problems, the prompt service was fast. Thanks
Posted by Jim S. on May 12th 2016
Installation was straight forward. Just follow the video. But, there is a problem with the detent. It's too strong. I now need to depress the detent to close the lever (using a small screw driver). Opening is another problem. The original part was easy to open. The new replacement now requires a small screw driver to overcome the strong detent spring when opening.
Posted by Dan / Western Washington State on May 12th 2016
I just purchased the slide release lever for the Ruger SR22. Absolutely precision fit and a very good You Tube video on installation. Pin is a little hard to remove and replace. Have a good punch and take your time. I also have the SR22 threaded barrel replacement which is very accurate and another high quality product. Great outfit with really good ideas.
Posted by Dennis Kolodny on Apr 18th 2016
Had my gunsmith install the SR22 takedown lever and he mentioned that it appeared to be of very high quality. He also said it was easy to install. A winner.
Posted by Phil Wagoner, Blackbird Arms on Mar 25th 2016
The Takedown Lever was nicely made and well finished. The only issue I have is that the detent ball is quite hard to depress when closing the lever. I use a small punch to depress it and it snaps into position tightly. My factory part had the top of the lever ripped right off down to the spring channel. I was testing suppressors and the extra back pressure beat the factory part to death in about 20 or so rounds.
One note for all those replacing the takedown lever - be sure the trigger bar return spring is straight in the grip assy. and the plunger is inserted in the sq. hole in the chassis BEFORE putting the two parts back together. I mangled my spring and had to rewind the spring on a drill bit twice. The video makes this seem easy and quick but it may not be. Take your time to get the spring and plunger started straight in both parts before you push them together.
Showing reviews 1-10 of 17 | Next
All prices are in USD